1 CANbus RESISTOR T20 W21/5W for Led Bulbs

Description1 Professional CANbus Filter Resistor for T20 W21/5W LED Bulbs | Error Free Warning, Anti Flicker Decoder | Plug & Play Chain-connected NO Modifications(WARNING: Success CANNOT Be Mathematics, but WE GUARANTEE the Money Back Guarantee = It Will Be Possible to Return the Product for a Total Refund) READ INFO in DESCRIPTION- Plug and Play (T20 - 7443 - W21/5W Connectors)- Quality of the Materials Used- It Removes the Error Warning- It Removes Flashes and Flickers- It Removes Radio InterferenceTHE PACKAGE INCLUDES:- 1X CANbus Filter Resistor T20, W21/5WINFO:Additional CANbus Resistor Control Unit, for Installation of T20 W21/5W LED Bulbs. Erases Errors and Malfunctions on Position Lights, Daytime Running Lights DRL, Reverse Lights, etc. Built with High Resistance Materials and Finishing, with ABS Body and Connectors.MINIMUM SIZEIt is currently the SMALLEST Electrolytic Condenser Filter on the marketIT HAS T20 W21/5W SOCKET LIKE YOUR CARNo need of adaptations or modifications of the cables, just Plug and PlayCANBUS NO ERRORS - NO FLICKERS - NO RADIO INTERFERNCESEquipped with 1000UF Capacitor (Microfarad) 12VHOW DOES IT WORKMany cars, after the installation of LED lamps (on Parcking light, Daytime Running Light DRL, Reverse Lights, etc) report the ERROR Warning, they FLASH when turn on, they TURN OFF after turning on, they have LOW POWER, in some cases, they interfere with RADIO reception.These phenomena are due to the CANbus control system of the car, which, following a LED installation, detects a lower absorption (Watt) than that of the classic halogen bulb; as a result, it detects the new LED bulb as having burnt out or failed.This type of filter is nothing more than an an electrolytic capacitor capable of increasing the perceived absorption, and filtering its voltage, to evade the CDB of the car.CASES OF NON-WORKINGIt may depend on 2 Factors; Led absorption much lower than stated; Restrictive Car CANbus. In These Cases you can RETURN the Product for a TOTAL REFUND COMPATIBILITY:- With T20 - 7443 - W21/5W LED bulbsFOR AN OPTIMAL ASSEMBLY, WE RECOMMEND:- INTRODUCTION: Keep the Original Halogen Bulb installed on one Headlight, While on the other proceed to the Test before installing the LED Bulbs.- CONNECT MALE SOCKET: Connect the Male socket of the Filter to the Car Headlight Connector- CONNECT FEMALE SOCKET: Connect the LED bulb to the female socket of the filter- CHECK: Start the vehicle to check if there are no problems, only then proceed to lock the LED bulb.- INSTALLATION: Repeat the operation on the second headlight IT IS PREFERABLE To Keep The Resistors Out Of The Headlight, as less overheating is Equal to LONGER LIFE of the LEDs.We do not take responsibility for: erroneous purchases - violations of regulations or laws of any state - damages, which you may cause to you, to third parties or to the same article, as we describe each individual specification in detail. We also remind you that, these are Aftermarket Items, designed for full compatibility and operation on the designated vehicle, but there remain products that may not be allowed for use on the public road.We trust in your common sense.

1PCS 1156 Ba15s P21W LED T20 7440 W21W W21/5W 1157 Bay15D LED Bulbs 144SMD Canbus Bau15s Py21W Lamp for Turn Signal Light - China 7440 W21W W21/5W, S25 1156 Ba15s

5W 186 Ohm Load Resistor - Warning Canceller - CANBus

7443 T20 Upgraded CANBUS LED Bulbs KaiDengZhe Red 20W W21/5W LED Bulb for Car Reverse Brake Tail Turn Signal Back Up Light Build-in Load Resistor Error Free Anti Hyper Flash for Blinker Bulb-2PCS : : Car & Motorbike